HOW TO INSTALL DSTV SATELLITE

HOW TO ASSEMBLE, TRACK AND INSTALL DSTV SATELLITE FROM THE BEGINNING TO THE END

Spread the love

DSTV MEANING

The Word DSTV simply means Digital Satellite Television which is a Sub-Saharan African direct broadcast satellite service owned by Multichoice. This company started providing services to their numerous subscribers estimated around 11.9 million as from 1995.

Now, learning how assemble, track and install DSTV Satellite would be a very big opportunity and also a very good source of making money.

Remember, you can learn it to know how to do it yourself or use it as a business and start making money from it.

STEPS TO FOLLOW

Buying of the DSTV SET, which comprises of the HD Decoder, 90cm Dish, a roll of Coaxial cable, and necessary connectors like F-Connector. The cost of buying DSTV Set varies depending on your location and promo time. In Nigeria,as of January, 2020, it costs #9,900 per set and the Installation costs between #4,000 – #5,000.

CHOOSING A BEST LOCATION TO MOUNT YOUR DSTV DISH

The important thing you must remember is that for you to get DSTV Signal very well, you must mount the Dish to face the East-Direction. Now, regardless of your environment, for you to know your East Direction from anywhere you are, is simply identifying the direction of Rising of the Sun.

Now, make sure there is no tree, building, or high tension electric wire very close to where you want to mount the Dish otherwise, it will block the signal,see images below

YOUR DSTV CAN BE MOUNTED ON THE BUILDING WALL OR THE DASH BOARD

The best place to fix your dish is on the building wall or on the top building concrete platform because it will be very firm not to be pushed down by the breeze or the rain.

Now, fix the bracket and the pole as shown below and tight them very well with 13 or 14 spanner as the case may require.

Now, attach the 90cm assembled blue dish on top of the bracket as shown below

Next, attach your satellite finding meter to the dish so as to enable you track a very high signal point.

GO INSIDE THE HOUSE AND CONNECT THE DSTV DECODER TO THE TV

Ok, when you open the decoder carton, you will see the DSTV Decoder box, HDMI wire, AV wire, Remote control with the battery and the Power Adapter plug. Connect everything properly, fix the coaxial cable with the F-Connector and attach it to the LNB IN Port at the back of the Decoder as shown below

Now, the coaxial cable attached to the LNB IN should go outside and fixed at the LNB port on top face of the dish while the HDMI cable will go into the TV HDMI port or the AV wire respectively and the Power cord going into the socket for power supply, see images below

NOW POWER-ON THE DSTV DECODER

Note, as you on your DSTV decoder, the first thing it will do is to boot, after booting you will this first time Installation Wizard displays on your screen as shown below

So, just follow the prompt message and continue. Therefore, if your language is English,Press OK and you will see

This is step 2 of 5, use your DSTV remote and change the IS20 to E36B and Press OK to continue as below

When you press ok, it will take you to step 3 of 5, and this will appear as seen below

So, use your remote and select the Manual Setup and not Quick Setup. After doing that Press OK and it will land you into the Step 4 of 5 where you will be shown the Tuner 1 Signal Status and Tuner 2 Signal Status as displayed under,

Now, this is the stage where you need to move outside and do your signal tracking with the dish, because this Tuner 1 and Tuner 2 will help you to know when exactly you have gotten the signal of the DSTV SATELLITE. Therefore, immediately you move outside, raise the tuning nob of the Satellite Finder to number 5 and start moving your dish in an UP and DOWN direction, once you reaches the signal point, the meter will sound very high the value will increase from 5 to 10 and above. Then, start tightening your dish’s bolts and nuts very well. At this point, when you go inside, will observe the Tuner 1 and Tuner 2 Signal Status filled with blue lines as shown below

Now, you have done a very great work indeed because you have rightly gotten the Signal with which the DSTV Decoder will be able to run a full Scan of all the Channels contained in DSTV network.

Note, at this stage, if you do not get the Signal very high, the DSTV decoder will not be able to scan any Channel at all. So, you MUST work very hard to ensure you get it right and you are good to go.

Now Press OK in the remote to make the decoder to Start Scanning all the Channels as seen below

Immediately the DSTV decoder finish scanning, it will automatically start showing the Channel 100 which is the FREE Channel and now you can call the customer care lines to open the remaining Channels for you or you can as well send in a Text message ” RESET one space IUC NO send to 30333” if the DSTV Decoder has been Activated then, all the Channel in that bouquet will start showing in no distant time. congratulations!!! You have done it. You will start viewing all your Channels as seen below,

This is how to Track and Install a DSTV SATELLITE starting from the beginning to the End. Powered by ROFIX TECHNOLOGIES. WHATSAPP +2348065545733, E-mail: info@rofixtech.com, rofixtech@gmail.com

Hi friends, did you find our posts helpful? Please leave a comment with us.